Oferta

BLITZ F411 1S Whoop AIO – w/Rx

 60.00

-14%
BLITZ F411 1S Whoop AIO - w/Rx  70.00  60.00
Solo 1 artículos que quedan en stock!

 

GRACIAS por apoyar un pequeño negocio!

Sitio web garantizado con pago seguro

BLITZ F411 1S Whoop AIO – w/Rx

PRODUCT DESCRIPTION

What if you could get the combined MCU speed and ESC power of a big stack, but carefully arranged on a 25×25 whoop size board? That would be crazy right? Well, we just did it…

This is

Features

SUPPORT BLHELISUITE PROGRAMMABLE

BUILT IN 2.4G CC2500 RECEIVER

5A CONTINUOUS CURRENT

SUPER LIGHT ONLY 4.8G

MCU:STM32F411

POWER SUPPLY: 1S

GYRO: BMI270

FC Specifications

Weight: 4.8g (with power cable, VTX, and VTX antenna)

Mounting pattern: 25.5*25.5mm/φ3mm (half-hole)

Supported Protocols: CC2500, SPI, D8, S-FHSS

FC Firmware: IFLIGHT_BLITZ_F411RX

BEC output: 5V 500mA

Connector: Micro-USB

MCU: STM32F411

INA pad: n uart2

Barometer: NO

Size: 29*29mm

Gyro: BMI270

Blackbox: NO

NOTE: F.PORT protocol RX input support, telemetry not supported.

ESC Specifications

ESC // 5A

Signal Support: Dshot, Oneshot, Multishot

Current: 5A continuous and peak 6A

ESC Firmware: O-H-30 BLS 16.8 (BlheliS) / Bluejay Q-H-50 (Bluejay)

Current sensor: yes

ESC Telemetry: NO

Current scale: 400

Input: 1S

VTX Specifications

Protocol: Smart audio

Power: PIT/25/50mW

Connector: UFL/IPEX

Input voltage: 5V

Channels: 48CH

Packing List

1 x BLITZ F411 1S 5A Whoop AIO Board with Built-in 2.4G CC2500 Receiver / 2.4G ELRS w/SMD Antenna (As optional)

4 x M2 Rubber Balls

1x Whip antenna

our new iFlight BLITZ series AIO FCs for your ultimate build. A future proof all-in-one FC to step up the game and make some more room for future flight firmware development like Betaflight, Emuflight etc. Lightweight, minimum size, minimum work.This could only be achieved by using BGA chipsets instead of ordinary QFP (big size) MCUs and ultra powerful Mosfets for almost any build. Solder your motor wires on and let’s go! DJI Plug&Play plug and so many UARTs most people wouldn’t even use em’ all. Compatible to digital and analog FPV, onboard Barometer for possible long range flights and much more. Unleash the beast!

Top Features:

  • Vista digital system Plug-and-Play (VBAT passthrough)
  • MCU: BGA-STM32F745, 216MHz
  • OSD: AT7456E
  • Blackbox: 16MB Onboard Flash
  • Gyro: MUP6000

Safety reminder:

The DJI plug&play port has no voltage regulator (BEC) and is passing through VBAT. The Caddx Vista goes up to 26.4V (6S), the DJI Air Unit goes up to 17.6V (4S). Make sure not to plug-in your DJI Air Unit directly when you’re flying 6S, because this would fry it! BEC to add for your 6S build can be found here: https://shop.iflight-rc.com/index.php?route=product/product&product_id=747

Small motor 4S builds should usually need an additional capacitor of at least 16V/220uF, for 6S go up to 35V or even 50V. Bigger motors have a bigger current draw, higher voltage spikes and more serious back EMF (motor braking, works like a generator). Make sure to add big enough or even bigger low ESR capacitors on the AIO battery pad or on your battery lead the more aggressive motors you fly. There’s a choice of capacitors in the package, but it’s never a bad idea to make sure to protect your board. Smaller boards have less capacitance which has to be covered with external capacitors, there’s no way around.

FC // BLITZ F7 AIO

Specification:

  • MCU: BGA-STM32F745
  • Gyro: MUP6000
  • Blackbox: 16MB Onboard Flash
  • BEC output: 5V 2.5A
  • Barometer: DPS310
  • Connector: Micro-USB
  • OSD: IFLIGHT OSD (AT745E)
  • FC Firmware:IFLIGHT_F745_AIO
  • ESC Firmware:G-H-50 BLS
  • Mounting pattern: 25.5*25.5mm φ3mm
  • Dimensions: 32.5*32.5mm
  • Weight: 8.5g

ESC // 55A 2-6S

Specification:

  • Uarts: 5
  • Current Sensor: Yes
  • Input: 2-6S LIPO
  • Current scale: 100
  • Current sensor:Yes
  • Constant: 55A / Burst: 60A
  • ESC MCU:8BB21
  • BLHeli: BLHeli-S
  • Telemetry: No
  • ESC Firmware: G-H-30 BLS
  • Mounting pattern: 25.5*25.5mm/Φ3mm
  • Dimensions: 32.5*32.5mm

Wiring suggestion:

UART1/4/7 for GPS or other sensors that require a serial port

UART2 for VTX HD/Analog Telemetry

UART3 for Receiver

Package Includes:

– BLITZ F7 AIO x 1

– Capacitor 470uF/35V x 2

– XT60 16AWG cable 100mm x 1

– XT30U 18AWG cable 70mm x 1

-1.0-7P cable 50mm-28mm x 1

-1.0-7P cable 50mm x 1

– M2 silicon grommets x 4

– M2*12mm screws x 8

– M2 Transparent Nylon Nut x 8

– 0.8mm black Heat shrink tube 10mm x 8

Diagram

BLITZ F411 1S 5A Whoop AIO Board with Built in CC2500 2.4G Receiver Wiring diagram

Información adicional

Peso N/D
Receiver option: Sin selección

ELRS 2.4Ghz, Frsky

Valoraciones

No hay valoraciones aún.

Sé el primero en valorar “BLITZ F411 1S Whoop AIO – w/Rx”

Tu dirección de correo electrónico no será publicada. Los campos obligatorios están marcados con *